• 4 1/2″ – 115 mm.
• Cutting, predominantly angled blades, superior finish.
• Suitable to applications which require cutting small material or performing small cut, soft metal strands (e.g. soft copper, gold, silver, magnetic wires).
• The strong blades are designed to apply moderate cutting force.
• The epoxy coating provides the tweezers with ESD properties suitable to electronic components handling and to clean room use.

Handle coating: Engineering coating type NE – N.

• This conductive polyester epoxy coating comprise essentially polyester and epoxy resins, plus the electrically conductive additives and light and heat resistance pigment.
• Easy to clean.
• Excellent dispersion.
• Impact-resistant surface and good elasticity.
• Functional permanent graffiti protection.
• Continuosly at temperature up to 120°C.
• ESD Safe coating with surface resistance 10⁵ Ohm – 10⁶ Ohm.
• Good resistance to many diluted acids and alkalis. Contact with organic solvents is possible conditionally and for short term. Resistance should be investigated for the case in question.

Body material: Carbon Steel type C.

• Carbon steel (Material number 1.1231, C67S, AISI 1070).
• Contains from 0,65 – 0,73 wt% carbon.
• Magnetizable.
• Will be hardened by heat treatment, max. hardness 60 HRC.
• Poor resistance to corrosion.
• Used where strength and/or hardness are of primary concern.
• Typical applications include tweezers and cutting tools for the electronic industry, watch-makers, jewelers applications.

• 3 3/4″ – 100 mm.
• Cutting micro tips, predominantly angled blades, superior finish.
• Suitable to applications which require cutting very small material or performing very small cuts, soft metal strands (e.g. Copper).
  
• The micro blades are designed to apply maximum cutting force while granting maximum visibility.

Body material: INOX (S).

• Martensitic higher carbon steel (Material number 1.4034, DIN X46Cr13, AISI number 420).
  
• Contains from 12.5 to 14.5 wt% chromium.
• Magnetizable.
• Can be hardened by heat treatment, forming should be done in the annealed condition.
• Less resistant to corrosion than the austenitic or ferritic grades.
• Used where strength and/or hardness are of primary concern and where the environment is relatively mild from a corrosive standpoint.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in mild aggressive chemical environments.

• 4 1/4″ – 115 mm.
• Cutting, fine tips, predominantly angled blades, superior finish.
• Suitable to applications which require cutting very small material or performing very small cuts, soft metal strands (e.g. Copper).
  
• The fine blades are are designed to apply maximum cutting force while granting maximum visibility.

Body material: CARBON STEEL (C).

• Carbon steel (Material number 1.1231, C67S, AISI 1070).
• Contains from 0,65 – 0,73 wt% carbon.
• Magnetizable.
• Will be hardened by heat treatment, max. hardness 60 HRC.
• Poor resistance to corrosion.
• Used where strength and/or hardness are of primary concern.
• Typical applications include tweezers and cutting tools for the electronic industry, watch-makers, jewelers applications.

• 4 1/4″ – 115 mm.
• Cutting, predominantly angled blades, superior finish.
• Suitable to applications which require cutting very small material or performing very small cuts.
  
• Suitable to cut small, soft metal strands (e.g. Copper).

Body material: CARBON STEEL (C).

• Carbon steel (Material number 1.1231, C67S, AISI 1070).
• Contains from 0,65 – 0,73 wt% carbon.
• Magnetizable.
• Will be hardened by heat treatment, max. hardness 60 HRC.
• Poor resistance to corrosion.
• Used where strength and/or hardness are of primary concern.
• Typical applications include tweezers and cutting tools for the electronic industry, watch-makers, jewelers applications.

• 4 3/4″ – 120 mm.
• Cutting, parallel blades, superior finish.
• Suitable to applications which require cutting small material or performing small cut, soft metal strands (e.g. soft copper, gold, silver, magnetic wires).
• The parallel blades allow cutting along the entire blade length.

Body material: CARBON STEEL (C).

• Carbon steel (Material number 1.1231, C67S, AISI 1070).
• Contains from 0,65 – 0,73 wt% carbon.
• Magnetizable.
• Will be hardened by heat treatment, max. hardness 60 HRC.
• Poor resistance to corrosion.
• Used where strength and/or hardness are of primary concern.
• Typical applications include tweezers and cutting tools for the electronic industry, watch-makers, jewelers applications.

• 4 3/4″ – 120 mm.
• Cutting, angled blades tips, superior finish.
• Suitable to applications which require cutting small material or performing small cut, soft metal strands (e.g. soft copper, gold, silver, magnetic wires).
• The strong blades are designed to apply moderate cutting force.

Body material: CARBON STEEL (C).

• Carbon steel (Material number 1.1231, C67S, AISI 1070).
• Contains from 0,65 – 0,73 wt% carbon.
• Magnetizable.
• Will be hardened by heat treatment, max. hardness 60 HRC.
• Poor resistance to corrosion.
• Used where strength and/or hardness are of primary concern.
• Typical applications include tweezers and cutting tools for the electronic industry, watch-makers, jewelers applications.

• 4 1/2″ – 115 mm.
• Cutting, predominantly angled blades, superior finish.
• Suitable to applications which require cutting small material or performing small cut, soft metal strands (e.g. copper).
  
• The short and strong blades are designed to apply maximum cutting force.

Body material: CARBON STEEL (C).

• Carbon steel (Material number 1.1231, C67S, AISI 1070).
• Contains from 0,65 – 0,73 wt% carbon.
• Magnetizable.
• Will be hardened by heat treatment, max. hardness 60 HRC.
• Poor resistance to corrosion.
• Used where strength and/or hardness are of primary concern.
• Typical applications include tweezers and cutting tools for the electronic industry, watch-makers, jewelers applications.

•  4 1/2″ – 115 mm.
• Cutting, predominantly angled blades, superior finish.
• Suitable to applications which require cutting small material or performing small cut, soft metal strands (e.g. soft copper, gold, silver, magnetic wires).
• The strong blades are designed to apply moderate cutting force.

Body material: CARBON STEEL (C).

• Carbon steel (Material number 1.1231, C67S, AISI 1070).
• Contains from 0,65 – 0,73 wt% carbon.
• Magnetizable.
• Will be hardened by heat treatment, max. hardness 60 HRC.
• Poor resistance to corrosion.
• Used where strength and/or hardness are of primary concern.
• Typical applications include tweezers and cutting tools for the electronic industry, watch-makers, jewelers applications.

• 4 1/2″ – 115 mm.
• Cutting, Tungsten Carbide insert (75 HRC), predominantly angled blades, superior finish.
• Suitable to applications which require cutting small material or performing small cuts.
• The extreme hard Tungsten Carbide blade insert is designed to cut the hardest metals.
  

Body material: STAINLESS STEEL (SA).

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
  
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.

•  4 1/2″ – 115 mm.
• Cutting, rounded, predominantly angled blades, superior finish.
• Suitable to applications which require cutting small material or performing small cuts. Suitable to cut small, soft metal strands (e.g. soft copper, gold, silver, magnetic wires).
• The short, rounded blades are designed to grant maximum visibility and to apply maximum cutting force.
  

Body material: CARBON STEEL (C).

• Carbon steel (Material number 1.1231, C67S, AISI 1070).
• Contains from 0,65 – 0,73 wt% carbon.
• Magnetizable.
• Will be hardened by heat treatment, max. hardness 60 HRC.
• Poor resistance to corrosion.
• Used where strength and/or hardness are of primary concern.
• Typical applications include tweezers and cutting tools for the electronic industry, watch-makers, jewelers applications.