• 4 3/4” – 120 mm.
• Fine, round, flat, straight tips.
• Suitable to applications which require holding a flat component firmly.
• The epoxy coating provides the tweezers with ESD properties suitable to electronic components handling and to clean room use.

Handle coating: Engineering coating type NE – N.

• This conductive polyester epoxy coating comprise essentially polyester and epoxy resins, plus the electrically conductive additives and light and heat resistance pigment.
• Easy to clean.
• Excellent dispersion.
• Impact-resistant surface and good elasticity.
• Functional permanent graffiti protection.
• Continuosly at temperature up to 120°C.
• ESD Safe coating with surface resistance 10⁵ Ohm – 10⁶ Ohm.
• Good resistance to many diluted acids and alkalis. Contact with organic solvents is possible conditionally and for short term. Resistance should be investigated for the case in question.

Body material: Stainless Steel type SA.

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.

• 5″ – 125 mm.
• Fine, sharp, straight tips.
• Suitable to applications which require holding a component firmly.
• The epoxy coating provides the tweezers with ESD properties suitable to electronic components handling and to clean room use.

Handle coating: Engineering coating type NE – N.

• This conductive polyester epoxy coating comprise essentially polyester and epoxy resins, plus the electrically conductive additives and light and heat resistance pigment.
• Easy to clean.
• Excellent dispersion.
• Impact-resistant surface and good elasticity.
• Functional permanent graffiti protection.
• Continuosly at temperature up to 120°C.
• ESD Safe coating with surface resistance 10⁵ Ohm – 10⁶ Ohm.
• Good resistance to many diluted acids and alkalis. Contact with organic solvents is possible conditionally and for short term. Resistance should be investigated for the case in question.

Body material: Stainless Steel type SA.

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.

• 4 3/4″ – 120 mm.
• Fine, pointed, straight tips.
• Suitable to applications which require holding a component firmly.
• The epoxy coating provides the tweezers with ESD properties suitable to electronic components handling and to clean room use.

Handle coating: Engineering coating type NE – N.

• This conductive polyester epoxy coating comprise essentially polyester and epoxy resins, plus the electrically conductive additives and light and heat resistance pigment.
• Easy to clean.
• Excellent dispersion.
• Impact-resistant surface and good elasticity.
• Functional permanent graffiti protection.
• Continuosly at temperature up to 120°C.
• ESD Safe coating with surface resistance 10⁵ Ohm – 10⁶ Ohm.
• Good resistance to many diluted acids and alkalis. Contact with organic solvents is possible conditionally and for short term. Resistance should be investigated for the case in question.

Body material: Stainless Steel type SA.

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.

• 4 1/4″ – 110 mm.
• As 3, short – Fine, pointed, straight tips.
• Suitable to applications which require holding a component firmly while granting good visibility.
• The short body allows a firmer grip combined with greater practicality.
• The epoxy coating provides the tweezers with ESD properties suitable to electronic components handling and to clean room use.

Handle coating: Engineering coating type NE – N.

• This conductive polyester epoxy coating comprise essentially polyester and epoxy resins, plus the electrically conductive additives and light and heat resistance pigment.
• Easy to clean.
• Excellent dispersion.
• Impact-resistant surface and good elasticity.
• Functional permanent graffiti protection.
• Continuosly at temperature up to 120°C.
• ESD Safe coating with surface resistance 10⁵ Ohm – 10⁶ Ohm.
• Good resistance to many diluted acids and alkalis. Contact with organic solvents is possible conditionally and for short term. Resistance should be investigated for the case in question.

Body material: Stainless Steel type SA.

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.

• 4 1/4″ – 110 mm.
• Fine, sharp, straight tips.
• Suitable to applications which require holding a component firmly.
• The epoxy coating provides the tweezers with ESD properties suitable to electronic components handling and to clean room use.

Handle coating: Engineering coating type NE – N.

• This conductive polyester epoxy coating comprise essentially polyester and epoxy resins, plus the electrically conductive additives and light and heat resistance pigment.
• Easy to clean.
• Excellent dispersion.
• Impact-resistant surface and good elasticity.
• Functional permanent graffiti protection.
• Continuosly at temperature up to 120°C.
• ESD Safe coating with surface resistance 10⁵ Ohm – 10⁶ Ohm.
• Good resistance to many diluted acids and alkalis. Contact with organic solvents is possible conditionally and for short term. Resistance should be investigated for the case in question.

Body material: Stainless Steel type SA.

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.

• 4 3/4″ – 120 mm.
• Fine, curved tips.
• Suitable to applications which require holding a component firmly while granting maximum visibility.
• The epoxy coating provides the tweezers with ESD properties suitable to electronic components handling and to clean room use.

Handle coating: Engineering coating type NE – N.

• This conductive polyester epoxy coating comprise essentially polyester and epoxy resins, plus the electrically conductive additives and light and heat resistance pigment.
• Easy to clean.
• Excellent dispersion.
• Impact-resistant surface and good elasticity.
• Functional permanent graffiti protection.
• Continuosly at temperature up to 120°C.
• ESD Safe coating with surface resistance 10⁵ Ohm – 10⁶ Ohm.
• Good resistance to many diluted acids and alkalis. Contact with organic solvents is possible conditionally and for short term. Resistance should be investigated for the case in question.

Body material: Stainless Steel type SA.

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.

• 6 1/8″ – 155 mm.
• Fine, bent, squared tips, superior finish.
• Suitable to applications which require holding a component firmly. The bent geometry provides maximum visibility and increased ergonomics.
• The epoxy coating provides the tweezers with ESD properties suitable to electronic components handling and to clean room use.

Handle coating: Engineering coating type NE – N.

• This conductive polyester epoxy coating comprise essentially polyester and epoxy resins, plus the electrically conductive additives and light and heat resistance pigment.
• Easy to clean.
• Excellent dispersion.
• Impact-resistant surface and good elasticity.
• Functional permanent graffiti protection.
• Continuosly at temperature up to 120°C.
• ESD Safe coating with surface resistance 10⁵ Ohm – 10⁶ Ohm.
• Good resistance to many diluted acids and alkalis. Contact with organic solvents is possible conditionally and for short term. Resistance should be investigated for the case in question.

Body material: Stainless Steel type SA.

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.

• The 775, SM103 and SM104 models.
• The epoxy coating provides the tweezers with ESD properties suitable to electronic components handling and to clean room use.

Handle coating: Engineering coating type NE – N.

• This conductive polyester epoxy coating comprise essentially polyester and epoxy resins, plus the electrically conductive additives and light and heat resistance pigment.
• Easy to clean.
• Excellent dispersion.
• Impact-resistant surface and good elasticity.
• Functional permanent graffiti protection.
• Continuosly at temperature up to 120°C.
• ESD Safe coating with surface resistance 10⁵ Ohm – 10⁶ Ohm.
• Good resistance to many diluted acids and alkalis. Contact with organic solvents is possible conditionally and for short term. Resistance should be investigated for the case in question.

Body material: Stainless Steel type SA.

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.

• 4 1/2″ – 115 mm.
• Cutting, predominantly angled blades, superior finish.
• Suitable to applications which require cutting small material or performing small cut, soft metal strands (e.g. soft copper, gold, silver, magnetic wires).
• The strong blades are designed to apply moderate cutting force.
• The epoxy coating provides the tweezers with ESD properties suitable to electronic components handling and to clean room use.

Handle coating: Engineering coating type NE – N.

• This conductive polyester epoxy coating comprise essentially polyester and epoxy resins, plus the electrically conductive additives and light and heat resistance pigment.
• Easy to clean.
• Excellent dispersion.
• Impact-resistant surface and good elasticity.
• Functional permanent graffiti protection.
• Continuosly at temperature up to 120°C.
• ESD Safe coating with surface resistance 10⁵ Ohm – 10⁶ Ohm.
• Good resistance to many diluted acids and alkalis. Contact with organic solvents is possible conditionally and for short term. Resistance should be investigated for the case in question.

Body material: Carbon Steel type C.

• Carbon steel (Material number 1.1231, C67S, AISI 1070).
• Contains from 0,65 – 0,73 wt% carbon.
• Magnetizable.
• Will be hardened by heat treatment, max. hardness 60 HRC.
• Poor resistance to corrosion.
• Used where strength and/or hardness are of primary concern.
• Typical applications include tweezers and cutting tools for the electronic industry, watch-makers, jewelers applications.