• 4 3/4″ – 120 mm.
• Very fine, round, flat, straight tips.
• Suitable to applications which require holding a flat component firmly. Reverse action helps to hold the component firmly in a resting position.

Body material: Stainless Steel type SA.

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.

• 4 3/4″ – 120 mm.
• Very fine, pointed, straight tips.
  
• Suitable to applications which require holding a small component firmly. Reverse action helps to hold the component firmly in a resting position.

Body material: Stainless Steel type SA.

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.

• 4 1/4” – 110 mm.
• Extra fine, sharp, straight tips.
• Suitable to applications which require holding a small component firmly while granting maximum visibility.
• Reverse action helps to hold the component firmly in a resting position.

Body material: Stainless Steel type SA.

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.

• 4 1/4” – 110 mm.
• Extra fine, very sharp, straight tips.
• Suitable to applications which require holding a small component firmly while granting maximum visibility.
• Reverse action helps to hold the component firmly in a resting position.

Body material: Stainless Steel type SA.

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.

• 4 1/2” – 115 mm.
• Fine, sharp, straight tips.
• Suitable to applications which require holding a small component firmly while granting maximum visibility.
• Reverse action helps to hold the component firmly in a resting position.

Body material: Stainless Steel type SA.

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.

• 4 1/4” – 110 mm.
• Extra fine tips, superior finish.
• Anti capillary, with lock-ring for handling electronic microscope grids.
  
• Suitable to applications which require holding a small component firmly while granting maximum visibility. Reverse action helps to hold the component firmly in a resting position.
• The particular shape of its tips prevents capillary effect, avoiding the possible upwards flow of liquid along the tweezers tips.

Body material: Stainless Steel type SA.

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.

• 4 1/2” – 115 mm.
• Very fine, curved tips.
• Suitable to applications which require holding a small component firmly while granting maximum visibility. Reverse action helps to hold the component firmly in a resting position.

Body material: Stainless Steel type SA.

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.

• 5″ – 125 mm.
• Very fine, round, flat, straight tips.
  
• Suitable to applications which require holding a flat component firmly. Reverse action helps to hold the component firmly in a resting position.
• The carbon fiber reinforced ESD and non-scratching properties.

Tip material: Engineering plastic type CF.

• PA66/CF30 – polyamide 66 reinforced with 30 wt% carbon fiber.
• ESD safe material, lead-free.
• High mechanical strength and toughness.
• Low friction, self lubricating properties, excellent wear and abrasion resistance.
• Heat stabilized, 130°C (continuos use) – 190° (short time).
• Very low coefficient of linear thermal expansion.
• Very high rigidity, excellent tensile and flexural strength (bend strength), fatigue and creep resistance.
• Good chemical resistance (oils, grease, fuels, non polar solvents), but not resistant to strong acids, alkalis, hot water or steam.
• Applications include handling of sensitive components and devices (electronic components, micro-mechanical parts, glass and ceramic substrates, etc.) where non-scratching is critical. Popular in standard ESD and general electronics assembly and lab applications.

Tip material: High-performance plastic type CP.

• PEEK – polyetheretherketone reinforced with carbon nano.
• ESD safe material 10⁵-10⁶ Ohm.
• Very hard, rigid, high tensile and flexural strength, very high wear resistance.
• High heat capability (260-300°C), good dimension stability, low thermal linear expansion coefficient.
• Excellent resistance to chemicals and aggressive agents, excellent resistance to thermal ageing.
• Typical applications include handling of components in cleaning/chemical/assembly processes also at high temperature (soldering).

Tip material: High-performance plastic type SV.

• PVDF – polyvinylidene fluoride carbon fiber reinforced.
• ESD safe material, (avoid powder attraction, sparks generation, ignition sources).
• Smooth surface, excellent mechanical strength and toughness.
• Heat stabilized, high heat capability, continuous use temperature up to 150°C.
• High purity (clean room and medical devices approved, low extraction value).
• Excellent chemical resistance to most aggressive substances (mineral and organic acid) and solvents (hydrocarbons, alcohols, halogenated), resistant to halogens.
• Outstanding resistance to hydrofluoric acid (40% conc., 90°C), nitric acid (50% conc., 90°C), hydrochloric acid (36% conc., 90°C).
• High abrasion resistant.
• Resistant to UV and nuclear radiation (sterilisation).
• Typical applications include handling of very scratch- and contamination-sensitive components, cleaning and etching processes.

Body material: Stainless steel type SA.

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.

• 5″ – 125 mm.
• Very fine, sharp, straight tips.
• Suitable to applications which require holding a small component firmly. Reverse action helps to hold the component firmly in a resting position.
• The carbon fiber reinforced ESD and non-scratching properties.

Tip material: Engineering plastic type CF.

• PA66/CF30 – polyamide 66 reinforced with 30 wt% carbon fiber.
• ESD safe material, lead-free.
• High mechanical strength and toughness.
• Low friction, self lubricating properties, excellent wear and abrasion resistance.
• Heat stabilized, 130°C (continuos use) – 190° (short time).
• Very low coefficient of linear thermal expansion.
• Very high rigidity, excellent tensile and flexural strength (bend strength), fatigue and creep resistance.
• Good chemical resistance (oils, grease, fuels, non polar solvents), but not resistant to strong acids, alkalis, hot water or steam.
• Applications include handling of sensitive components and devices (electronic components, micro-mechanical parts, glass and ceramic substrates, etc.) where non-scratching is critical. Popular in standard ESD and general electronics assembly and lab applications.

Tip material: High-performance plastic type CP.

• PEEK – polyetheretherketone reinforced with carbon nano.
• ESD safe material 10⁵-10⁶ Ohm.
• Very hard, rigid, high tensile and flexural strength, very high wear resistance.
• High heat capability (260-300°C), good dimension stability, low thermal linear expansion coefficient.
• Excellent resistance to chemicals and aggressive agents, excellent resistance to thermal ageing.
• Typical applications include handling of components in cleaning/chemical/assembly processes also at high temperature (soldering).

Tip material: High-performance plastic type SV.

• PVDF – polyvinylidene fluoride carbon fiber reinforced.
• ESD safe material, (avoid powder attraction, sparks generation, ignition sources).
• Smooth surface, excellent mechanical strength and toughness.
• Heat stabilized, high heat capability, continuous use temperature up to 150°C.
• High purity (clean room and medical devices approved, low extraction value).
• Excellent chemical resistance to most aggressive substances (mineral and organic acid) and solvents (hydrocarbons, alcohols, halogenated), resistant to halogens.
• Outstanding resistance to hydrofluoric acid (40% conc., 90°C), nitric acid (50% conc., 90°C), hydrochloric acid (36% conc., 90°C).
• High abrasion resistant.
• Resistant to UV and nuclear radiation (sterilisation).
• Typical applications include handling of very scratch- and contamination-sensitive components, cleaning and etching processes.

Body material: Stainless steel type SA.

• Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L).
• Contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements.
• Non-magnetizable (80%).
• Good corrosion resistance to most chemicals, salts and acids.
• Typical applications for the electronic industry, watch-makers, jewelers and laboratory and medical applications in moderately aggressive chemical environments.